Leading 10 usual forklift accidents ， forklift operation should take note of these matters ！.

Do not undervalue the forklift at the office. If the procedure is bad, there will certainly be serious mishaps in minutes, and there are lots of mishaps including forklifts.

Situation 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving mishap.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and hangs on the roadside shelf, which practically triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the personnel illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before starting.
3. When the forklift begins with a lots, the motorist should initially confirm that the lots is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is taking a trip, the fork must not be increased too expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be reduced to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will certainly create the automobile to lose side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the fire and slide, and it is restricted to brake all of a sudden while driving with tons unless there are special conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and should maintain a specific safety and security range from the lorry ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be properly slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the load should not block the driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it needs to drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, raised or driven, it is prohibited for workers to stand on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be fixed and reported in a timely fashion, and they will certainly never run with ailments or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between both forks should be readjusted as required to make the load of both forks balanced and not manipulated, and one side of the product ought Stand-on Electric Pallet Stacker to protest the rack. .
2. It is restricted to deal with a single fork or use a fork top or draw. In special conditions, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of filling and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be kept in mind that the fork pointer ought to not touch various other goods or objects. The lots should be supported with marginal Electric Forklift Truck for Warehouse back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for unique circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the gradient is above 10%, the vehicle must be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they encounter big or hefty products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the procedure.
1. Solitary fork operation is not permitted.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is purely prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Car park is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844